Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Westchester Homeowners Choose Therma-Tru Construction
We provide independent Therma-Tru construction service in Westchester, covering entry doors, patio sliders, and the sidelite and sill assemblies around them. What sets our Therma-Tru work apart is that we treat the door as part of the wall opening – sill, jamb, flashing and finish – not just a slab that gets swapped. We are not affiliated with, authorized by, or sponsored by Therma-Tru. We install and repair their products the same way we handle every other brand on our roster, with quality parts that fit the door and a written estimate before anything starts.
Westchester Construction Co runs seven service categories under one contractor: Driveways & Pavers, Fencing, Home Additions & ADUs, Bathroom Remodeling, Windows & Doors, Roofing, and Kitchen Remodeling. For Therma-Tru owners in Westchester, that breadth matters. A failed threshold often turns into a conversation about the floor inside, and a door replacement during a bathroom or kitchen rebuild is one line on one scope instead of two vendors arguing over who seals what. Our technicians have up to 9 years of experience. Call (888) 334-0815 for a free estimate.
Why Trust Westchester Construction Co for Your Therma-Tru Construction?
We work on Therma-Tru doors regularly as an independent contractor, so the familiarity is with how these products behave in South Florida heat and humidity, not how they look under showroom lighting. Fiber-Classic and Smooth-Star slabs, Professionals Series door systems with rot-resistant frames, and Therma-Tru patio and French door systems all share the same weak points in this climate: sills, sweeps, weatherstrip, hinge screws, and finish. We know where to look first.
When we service a door, we use OEM Therma-Tru sills, sweeps, weatherstrip and hinge parts where they are still available for that door system, and a quality aftermarket match only when the OEM part has been discontinued. That distinction protects the door and keeps the work warranty-safe: the frame stays original, the hardware stays compatible, and the repair doesn’t force a full replacement you didn’t need.
We are clear about our standing. We are an independent service provider and installer. We are not a Therma-Tru dealer, we don’t claim factory training or certification, and we don’t stock genuine Therma-Tru parts. What we offer is judgment built on repetition, a written line-item estimate, and the ability to fold door work into a larger Westchester project when the opening, the floor, or the adjacent room needs attention at the same time. If the honest answer is repair, you’ll hear repair. If it’s replacement, you’ll hear why.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Therma-Tru Construction Problems We Fix in Westchester
These are the failure modes we see most often on Therma-Tru doors in Westchester. Each one has a cause, and knowing the cause is what separates a fix that lasts from a patch that comes back after the next rainy season.
- Surface blistering and finish cracking on fiberglass slabs. Moisture gets behind the factory or field-applied topcoat, and the intense subtropical sun does the rest. The blistering usually starts on the face with the most sun exposure and spreads along the edges where the finish is thinnest. Once water is under the coating, sanding and repainting rarely holds; the slab itself may need to be replaced.
- Sill and threshold seal failure. Wind-driven summer rain works its way into the frame at the sill, especially where the seal has aged or the door was set on a slightly uneven threshold. The visible symptom is often subfloor staining or frame rot around the sidelites rather than water on the floor. By the time the stain shows, the seal has usually been failing for a while.
- Warping and sticking after thermal cycling. Doors that swell and drag on the jamb in summer and gap at the weatherstrip in cooler months are telling you the slab and frame are moving at different rates. It’s a common complaint on fiberglass entry doors in Westchester’s humidity, and it’s often fixable with hinge and weatherstrip adjustment rather than a new slab.
- Hardware and hinge screw pull-out. Screws back out of fiberglass slabs over time, particularly on doors that get heavy daily use. Once a hinge starts to pull, the door sags, the weatherstrip stops meeting the frame, and air and water get past the edge. Catching it early keeps the repair small.
- Failed weatherstrip along the door edge. Weatherstrip flattens and splits, and the door that sealed tight two seasons ago now lets water and air past the edge. Replacing the sweep and weatherstrip is inexpensive next to the damage a leaky edge causes at the sill and jamb.
A fiberglass entry door typically starts showing trouble as water staining at the threshold or a slab that sticks in the jamb after the rainy season. The usual cause is a failed sill seal or weatherstrip letting moisture into the frame, often combined with a factory finish breaking down on the sun-exposed face. A qualified local pro will pull the door, inspect the sill and jamb for rot, replace the threshold and weatherstrip, refinish or replace the slab as needed, and re-flash and seal the opening so the repair holds through the wet season.
Therma-Tru Parts & Our Repair-vs-Replace Approach
Our parts policy is simple: original Therma-Tru parts where they’re still made for the door system, a quality aftermarket match where they aren’t. That means OEM sills, sweeps, weatherstrip and hinge hardware when available – the parts designed to fit that frame and slab – and a close equivalent only when the original has been discontinued. We don’t claim to stock genuine Therma-Tru parts, and we won’t tell you a part is OEM if it isn’t.
The repair-or-replace call comes down to condition, not age. If the slab is sound and the failure is seals, hardware or weatherstrip, repair is the honest recommendation – it’s less money and the door keeps its original frame and finish. If the frame or slab shows rot, blistering or delamination, replacement is usually the better spend, because no amount of resealing fixes a slab that’s already absorbing water. We put the reasoning in writing so you can see what we found and why we recommend what we recommend.
Call (888) 334-0815 to schedule a free estimate on your Therma-Tru door and get a written line-item scope before any work begins.
Our Therma-Tru Service Process – Step by Step
- 1
Diagnosis. We pull the door and inspect the slab, sill, jamb, sidelites and flashing. We check for rot behind the seal, look at how the finish is holding on the sun-facing side, and test the weatherstrip contact along the edge. The diagnosis tells us whether the failure is hardware, seal, or structure.
- 2
Repair or install. If it’s seals and hardware, we install OEM Therma-Tru sills, sweeps, weatherstrip and hinge parts where available, then adjust the slab for proper clearance. If it’s a replacement, we set the new door system level, shimmed and flashed to the opening, and seal the threshold.
- 3
Test. We check the door swing, weatherstrip contact and latch alignment, then water-test the threshold and seal the way the opening will face weather during the rainy season. A door that tests dry at the sill is a door that stays dry.
- 4
Warranty-safe handoff. We leave you with a written record of the parts used and the work done. If the door is still under a Therma-Tru warranty, that record is what a warranty claim needs, and we keep our repairs compatible with the original system.
See the difference
Before
After
Before
After
Before
AfterTherma-Tru Products We Service & Install in Westchester
We service and install Therma-Tru fiberglass entry door collections, including Fiber-Classic and Smooth-Star, along with Professionals Series door systems built on rot-resistant frames. Therma-Tru patio and French door systems are part of the same work, and so are the sidelites, sills, thresholds, sweeps and weatherstrip that surround them.
Beyond the door itself, we handle the opening: re-flashing and sealing a threshold, repairing frame rot around sidelites, and finishing the interior and exterior around a new door. In Westchester, where homes sit on built-out mid-century lots with little room to maneuver, a door replacement often touches the wall, the stucco and the floor inside. We can take that on as one coordinated scope rather than handing you off to a separate finish carpenter and stucco contractor. We don’t claim to stock any of these products; we recommend based on what fits your opening and your budget.
We Also Service These Brands
Therma-Tru is one brand among many we install and service. Cabinetry from KraftMaid, engineered stone surfaces from Cambria and Silestone, and plumbing fixtures from Kohler all fall within our seven service categories. You choose the brand; we handle the build. That means a Westchester door replacement can sit alongside a kitchen or bathroom scope without a second contractor, and the material choices stay yours rather than ours.
FAQs – Therma-Tru Construction Service in Westchester
No. We are an independent service provider, not an authorized Therma-Tru dealer or factory-certified installer. We install and repair Therma-Tru products alongside other brands, and we tell you that up front so expectations are clear from the first call.
Yes. We use OEM Therma-Tru sills, sweeps, weatherstrip and hinge parts where they remain available for the door system, and a quality aftermarket match only where the original has been discontinued. We don’t claim to stock genuine Therma-Tru parts, and we’ll tell you which parts went into your door.
A hardware and weatherstrip repair is typically a single visit, while pulling a door and re-flashing a threshold takes longer because the opening has to be inspected and resealed. Replacement of a door system takes longer still. Call (888) 334-0815 for an exact timeline based on what we find at your door – estimates are free.
We cover fiberglass entry door collections including Fiber-Classic and Smooth-Star, Professionals Series door systems on rot-resistant frames, and Therma-Tru patio and French door systems, plus the sidelites, sills and weatherstrip around them. If you’re unsure whether your door falls within that scope, call and describe it.
Proper service using parts that fit the door system is designed to work with the original warranty, not against it. We keep a written record of the parts used and the work done, which is what any warranty claim needs. We’re an independent provider, so the final say on warranty coverage belongs to Therma-Tru; call (888) 334-0815 to discuss your specific door.
Typical estimated ranges depend on scope. Door and opening replacement generally falls in the $4,500 – $15,000 range for the replacement scope, while a bathroom remodel runs $9,000 – $28,000 and a full kitchen remodeling $14,000 – $45,000. These are estimates only; the written estimate sets the final price. Call (888) 334-0815 for an exact quote – estimates are free.
| Service | Typical Estimated Range |
|---|---|
| Window Replacement (door/opening replacement scope) | $4,500 – $15,000 |
| Bathroom Remodel | $9,000 – $28,000 |
| Full Kitchen Remodeling | $14,000 – $45,000 |
Sometimes. If the blistering is confined to the finish and the fiberglass underneath is sound, refinishing can work. Once moisture has delaminated the slab itself, replacement is usually the better spend. We inspect the slab and give you the honest call, in writing.
Thermal cycling. The slab and frame expand and contract at different rates in Westchester humidity, so the door drags on the jamb when it’s hot and pulls away from the weatherstrip when it cools. Hinge and weatherstrip adjustment usually fixes it without replacing the door.
A failed sill seal or degraded weatherstrip letting wind-driven rain into the frame. Pooling water at the threshold is a warning sign of frame rot around the sidelites, so it’s worth inspecting early rather than waiting for staining to show.
Often, but not always. OEM sills, sweeps, weatherstrip and hinge parts are available for many door systems, and where they’ve been discontinued we match a quality aftermarket part that fits. We’ll tell you which you’re getting before we install it.
Yes, when it’s part of the same scope. Because we handle windows and doors alongside kitchen and bathroom remodeling, a door replacement can be planned into the same project and the same written estimate rather than treated as a separate vendor line. Call (888) 334-0815 to talk through the combined scope.
Book Your Therma-Tru Service in Westchester, FL
Whether your Therma-Tru entry door is sticking, blistering or leaking at the threshold, we’ll inspect it honestly and tell you whether it can be saved or needs replacing. We handle fiberglass entry doors, patio and French door systems, and the sidelite and sill assemblies around them, all backed by a written line-item estimate. Call (888) 334-0815 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Written by the team at Westchester Construction Co.
Written by the team at Westchester Construction Co.