Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Westchester Homeowners Choose PGT Construction
We provide independent PGT construction service in Westchester, FL. PGT is a Florida-rooted manufacturer, which means its windows and doors are engineered for wind-borne debris codes and Florida humidity rather than being adapted to them later. That distinction matters in Westchester because so much of the housing stock is 1950s – 1970s concrete block and stucco on tight mid-century lots, where every opening has to satisfy the Florida Building Code’s wind-load and impact requirements and still fit a wall that was never framed for a modern unit.
Our role is straightforward: we connect Westchester homeowners with independent local professionals who know PGT’s product families and the installation details that keep their ratings intact. Westchester Construction Co is not affiliated with, authorized by, or a dealer for PGT. We’re an independent provider. You can reach us at (888) 334-0815. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- We service and install PGT impact windows and sliding glass doors as an independent provider, not a factory channel.
- Impact-rated glass and hardware must be replaced with rated components, or the opening loses the protection it was permitted for.
- Fogged laminated glass, dragging sliders and unflashed sills are the three calls we hear most from Westchester owners.
- Typical estimates run $8,000 – $25,000 for impact window installation and $4,500 – $15,000 for standard window replacement. The written estimate sets the final price.
Why Trust Westchester Construction Co for Your PGT Construction?
Our technicians have up to 9 years of experience, and a good share of that time has gone into impact-rated openings on Florida homes. PGT products aren’t complicated to a trained eye, but they’re unforgiving of shortcuts. A WinGuard unit is a laminated-glass assembly in a reinforced frame, and the performance it was tested for depends on the frame staying true, the sill pan flashing correctly, and the weatherstrip and perimeter sealant holding. Change one of those and the unit still looks fine for a few seasons before it starts telling you otherwise.
We work with quality parts that fit PGT equipment. On impact-rated units that means genuine PGT replacement parts for rollers, latches, weatherstrip and glass, because substituting non-rated hardware or glass voids the rating that protects the home. That’s not a sales line, it’s how the code works. Sourcing those parts takes familiarity with PGT’s product families and the willingness to wait for the right component rather than force a universal one into a rated opening.
We also treat the warranty question honestly. We’re independent, so we can’t speak for PGT, and we won’t pretend to. What we can do is perform work in a way that respects the rated assembly, document what was changed, and tell you when a repair would step outside what the manufacturer would stand behind. That’s a conversation worth having before the work starts, not after.
Westchester Construction Co handles windows and doors as one of seven service categories, alongside roofing, driveways and pavers, fencing, home additions and ADUs, bathroom remodeling and kitchen remodeling. When a PGT opening has water intrusion, the cause is sometimes the window and sometimes the roof edge or the stucco above it. Having all of that under one contractor means one accountable party instead of two trades pointing at each other.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common PGT Construction Problems We Fix in Westchester
The subtropical Miami climate is hard on openings in a specific way: intense sun on one elevation, driven summer rain on another, high humidity most of the year, and hurricane season from June through November. Westchester’s older CBS homes were built tight to side and rear property lines, which means exterior work is often done from a narrow access and repairs get deferred. Here’s what actually fails.
- Failed glazing seals on WinGuard impact units. Fog or a milky haze appears between the laminated glass and the outer pane. The glass itself hasn’t broken; the seal at the edge has given up after years of heat cycling. It’s cosmetic at first and a real clarity problem later, and it’s not something a cleaning product will touch.
- Water intrusion at slider thresholds and sill pans. PGT Aluminum Series sliding glass doors sit in an opening that has to drain. When the original install skipped proper flashing or weep provisions, water finds the one path it wants and shows up inside the wall or on the floor a few feet in. By the time it’s visible indoors, the framing around the opening has usually been wet for a while.
- Roller, track and latch wear on aluminum and vinyl sliders. Panels get heavy to slide, then stop latching cleanly. Grit, sun exposure and years of use wear the rollers and flatten the track. A slider that won’t lock is a security issue and, on an impact-rated unit, a sign the assembly isn’t seating the way it was designed to.
- Seal and weatherstrip deterioration with perimeter caulk breakdown. Sun and salt exposure break down the sealant line at the frame perimeter and the weatherstrip inside the jamb. It starts as a draft or a faint whistle in wind and turns into water tracking behind the stucco. Recaulking without checking the weatherstrip only fixes half the problem.
- Distorted frames and out-of-square openings. Sometimes the window isn’t the failure at all. Settling, a prior addition, or a rough opening that was never square puts a twist into the frame that no amount of adjustment will correct. That’s when the honest conversation shifts from repair to replacement.
A typical situation we hear described goes like this. A homeowner notices a WinGuard slider that no longer latches cleanly and drags along the bottom track, often after years of sun exposure and grit buildup. The usual culprits are worn rollers, a bowed track, or deteriorated weatherstrip and perimeter sealant allowing water past the threshold. A qualified local pro typically pulls the panel, assesses roller and track condition, replaces the hardware with rated components, re-flashes or reseals the opening as needed, and verifies the unit still closes and locks to its impact-rated configuration.
PGT Parts & Our Repair-vs-Replace Approach
Genuine PGT replacement rollers, latches, weatherstrip and glass are the right call for impact-rated units. Substituting non-rated glass or hardware voids the rating that protects the home, which quietly turns a rated opening into an ordinary one. We don’t stock or carry OEM or genuine PGT parts, and we’re not a dealer, but we can source and install quality parts that fit your equipment.
The repair-or-replace decision comes down to structure. Where the frame and surrounding structure are sound, targeted repair is the honest recommendation. Replace the rollers, fix the track, renew the weatherstrip, reseal and re-flash the perimeter, and the unit goes back to doing its job. Full replacement is justified when frames are distorted, when the glass is compromised, or when the opening was never flashed correctly in the first place. In that last case a new unit dropped into a bad opening fails on the same schedule as the old one.
On Westchester homes, that call gets complicated by how the original openings were built. Mid-century CBS walls don’t always have the framing a modern impact unit expects, and additions built decades ago sometimes moved the geometry. We look at the opening before we quote the window.
If you’re unsure which side of that line your PGT units fall on, call (888) 334-0815 and we’ll walk through it with you.
Our PGT Service Process – Step by Step
- 1
Diagnosis. We look at the unit in place and separate the window’s condition from the opening’s condition. Fogged glass gets assessed separately from a wet sill, because they’re different repairs with different causes. On Westchester homes, we also confirm the rough opening is square and the flashing detail is intact before recommending a fix.
- 2
Repair or install. For repair, we replace worn rollers, latches and weatherstrip with rated components and correct the track. For install, we set the PGT unit to the manufacturer’s instructions, flash the sill pan properly with weep provisions, and confirm the perimeter is sealed and caulked. Impact openings are permitted work in Miami-Dade County, so permit and inspection are part of the scope.
- 3
Test. Every slider gets operated through its full range. Every latch gets checked. Weep paths get verified by water. If the panel still drags or the lock doesn’t engage cleanly, the job isn’t finished.
- 4
Warranty and documentation. We hand over a record of what was replaced and what was left alone, so you have something to produce if a warranty question ever comes up.
See the difference
Before
After
Before
After
Before
AfterPGT Products We Service & Install in Westchester
We work with PGT WinGuard Aluminum Impact Resistant windows and PGT WinGuard Vinyl Impact Resistant windows, the two families most Westchester owners end up choosing between when they’re weighing frame strength against thermal performance. We also service and install PGT Aluminum Series sliding glass doors, along with PGT WinGuard Vinyl Single-Hung and Sliding windows. On the service side, the list runs from fogged glass and failed seals through roller, track and latch replacement, weatherstrip renewal, threshold re-flashing and perimeter resealing. We’re an independent provider, so we’ll tell you plainly what we can source and what has to come through a PGT channel.
We Also Service These Brands
We’re not tied to a single manufacturer. Alongside PGT we work with KraftMaid cabinetry, Cambria and Silestone engineered stone surfaces, and Kohler plumbing fixtures, among a much broader roster of name-brand products. Westchester Construction Co’s seven service categories let us handle a PGT window replacement, a kitchen remodel with Cambria counters and a roof repair as one coordinated project with a single point of accountability. You pick the brand. We handle the build.
FAQs – PGT Construction Service in Westchester
No. We’re an independent PGT service provider, not affiliated with, authorized by, or a dealer for PGT. We service and install PGT products with quality parts that fit them, and we’re clear about where our knowledge stops and the manufacturer’s begins. Call (888) 334-0815 for a free estimate.
Yes, with an important qualifier on impact-rated units. Your PGT equipment gets parts made to fit it, not universal substitutes, and on rated openings that means rated hardware and glass. We don’t stock OEM or genuine PGT parts, but we can source quality parts that fit your equipment and install them correctly. Call (888) 334-0815 to talk through your specific unit.
Most repairs, like a roller, latch or weatherstrip replacement, are completed in a single visit. Replacement projects take longer because impact openings in Miami-Dade County involve permits and inspection, and product lead time is part of the schedule. We set the timeline in the written estimate so you know what you’re planning around. Call (888) 334-0815 to start.
Impact windows and sliding glass doors, including the WinGuard aluminum and vinyl impact resistant window families and PGT Aluminum Series sliding glass doors. That covers installation, replacement, repair, and storm or water damage work on those units. Call (888) 334-0815 and describe what you have.
Not if it’s done correctly. Warranty coverage generally turns on whether rated components were retained and whether the unit was installed to specification, so using rated glass and hardware and flashing the opening properly is what protects you. We’re independent, so confirm specifics with PGT directly. Call (888) 334-0815 to discuss the work you need.
Typical estimated ranges for Westchester are below. They’re estimates, and the written estimate sets the final price.
| Service | Typical Estimated Range |
|---|---|
| Impact Window Installation | $8,000 – $25,000 |
| Window Replacement | $4,500 – $15,000 |
| Roof Repair (where intrusion traces to the roof edge) | $400 – $1,800 |
Call (888) 334-0815 for an exact quote. Estimates are free.
Often the glass unit has to be replaced rather than repaired. Fog between the laminated glass and the outer pane means the edge seal has failed, and resealing an impact-rated insulating unit in the field isn’t something that restores the rating. If the frame is sound, a glass replacement keeps the rest of the assembly in service. If the frame is distorted, replacement makes more sense. Call (888) 334-0815 and we’ll look at it with you.
Worn rollers and a flattened track are the usual reason. As rollers wear, the panel drops slightly and the bottom edge rides against the track instead of rolling in it. Grit accelerates the wear. Sometimes the track itself has bowed from sun exposure or a settling frame. Replacing the rollers with rated components fixes most of these. Call (888) 334-0815 for a free estimate.
More often the installation than the window. A sealed impact unit doesn’t let water through the glass, so if water appears at the sill or inside the wall, the likely culprits are missing or blocked weep provisions, flashing that was skipped at the original install, or perimeter sealant that has broken down. That’s diagnosable in one visit. Call (888) 334-0815 to schedule it.
You need hardware rated for that assembly, which in practice means genuine PGT components or a direct equivalent the manufacturer would stand behind. A generic roller or latch from a hardware aisle can physically fit and still compromise the rated assembly. That’s a risk we won’t take on an impact opening. Call (888) 334-0815 to talk through your options.
Three things decide it: whether the glass is compromised, whether the frame is still square and undistorted, and whether the opening was ever flashed correctly. If the glass and frame are intact and the opening drains, repair is the answer. Distortion or compromised glass points to replacement. Call (888) 334-0815 for a free assessment.
Book Your PGT Service in Westchester, FL
Whether it’s a fogged WinGuard unit, a slider that won’t latch, or a full impact window replacement on a mid-century Westchester home, we’ll give you a straight read and a written line-item estimate at no cost. Call (888) 334-0815. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Westchester Construction Co.