Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Westchester Homeowners Choose Mr-Glass Construction
We provide independent Mr-Glass construction service in Westchester, FL, and what sets our work apart is that we’re not tied to Mr-Glass sales quotas or proprietary part markups. We can specify the right glass, frame, and hardware for Florida’s wind and humidity conditions without brand bias. Our estimators and installers have worked with Mr-Glass enclosures across Westchester for years, which means we know exactly where these systems fail and how to correct them.
Westchester is built out. There’s no vacant land left in this unincorporated stretch of Miami-Dade, so nearly every job we see is a rebuild, an addition, or a tear-down on a mid-century lot. That reality shapes a Mr-Glass project before anyone touches glass. Tight lot lines, county inspectors, and the post-Surfside 40-year recertification regime all run in the background of what is, on the surface, a bathroom or enclosure upgrade. We handle that complexity as one contractor across every trade.
One clarification we like to get out front: Westchester Construction Co is not affiliated with or authorized by Mr-Glass. We’re an independent service provider. You choose the brand; we handle the build. Call (888) 334-0815 to talk through your Mr-Glass project.
Why Trust Westchester Construction Co for Your Mr-Glass Construction?
Our technicians have up to 9 years of experience, and that time shows most in the details of Mr-Glass work. We know how the roller assemblies wear, where the clear vinyl sweeps harden and shrink in Miami’s humidity, and why a 1/2-inch frameless door starts to sag years before anyone notices the wall anchors loosening. Those aren’t cosmetic problems. A sagging door that won’t close flush means water is already finding its way into places it shouldn’t.
We repair, install, and service Mr-Glass equipment with quality parts that fit it. When OEM rollers, hinges, and sweeps are available, we source them to preserve fit and finish. When they’re discontinued or priced out of reason, we use tested aftermarket stainless-steel and brass hardware that meets or exceeds original specs. That’s the practical benefit of an independent shop: we answer to the fit and the finish, not to a parts catalog.
Warranty-safe practices matter too. We pull the door properly, check the track for mineral buildup, and re-level before reinstalling. We don’t force hardware past its limits or drill new anchor points into old tile backer without assessing what’s behind it. That care keeps your enclosure working the way it was built to.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Mr-Glass Construction Problems We Fix in Westchester
Most calls we get about Mr-Glass products in Westchester trace back to a handful of predictable hardware failures. Here’s what we see, and why it happens.
- Roller and track failure on sliding shower doors. Plastic wheels flatten or crack over time, so the door jumps the track and water leaks at the base. It’s one of the most common calls we get, and it rarely has anything to do with the glass itself.
- Sweep and seal degradation on frameless enclosures. The clear vinyl sweep hardens and shrinks in Florida humidity, letting water escape onto bathroom floors. The sweep is a wear part, and treating it like one prevents bigger water damage.
- Hinge sag and glass misalignment on heavier 1/2-inch frameless doors. Wall anchors loosen over time, especially in older Westchester drywall or tile backer. The door droops, stops closing flush, and stresses the glass every time it’s used.
- Mineral staining and etching on uncoated panels. Hard water leaves permanent marks that no amount of cleaning removes, and owners often mistake them for soap scum. Once etching sets in, resurfacing isn’t an option.
- Corrosion at the frame and hardware. Between heavy summer rains and high interior humidity, exposed metal at the base and hinges deteriorates faster than most owners expect. Catching it early keeps a repair from turning into a full replacement.
None of these failures require a panic. Most are corrected with the right rollers, sweeps, and hinge hardware and a careful re-level.
Mr-Glass Parts & Our Repair-vs-Replace Approach
We don’t stock or carry genuine Mr-Glass parts, and we’re not a Mr-Glass dealer. What we do is source quality parts that fit Mr-Glass equipment. Where OEM rollers, hinges, and sweeps are available, we use them to preserve fit and finish. Where they’re discontinued or overpriced, we use tested aftermarket stainless-steel and brass hardware that meets or exceeds original specs. We’re not factory-trained or certified by Mr-Glass, but we’ve worked with these enclosures long enough to know which parts hold and which don’t.
Deciding between repair and replacement comes down to the glass. If the glass is etched, chipped, or the frame is corroded through, we’ll price a full replacement alongside the repair so you can see the break-even point honestly. Sometimes a $400 hardware refresh buys you another several years. Sometimes it doesn’t, and we’ll say so.
Call (888) 334-0815 to get a free estimate on your Mr-Glass repair or install.
Our Mr-Glass Service Process – Step by Step
- 1
Diagnosis. We inspect the rollers, track, sweeps, hinges, and wall anchors to find the actual source of the leak or misalignment, not just the symptom.
- 2
Repair or install. For repairs, we pull the door, replace worn hardware with stainless or nylon components, and check the track for mineral buildup. For new installs, we set the frame plumb and level against the existing backer and tile.
- 3
Test. We operate the door through its full travel and run water to confirm no leaks at the base and no binding in the track.
- 4
Warranty and handoff. We walk you through what was replaced, how to keep the sweep and track clean, and what your written estimate and warranty cover going forward.
A typical Mr-Glass sliding shower door starts leaving a puddle on the floor after a few years. The cause is usually worn rollers and a hardened vinyl sweep, not the glass. A qualified installer pulls the door, replaces the roller assembly and sweep, checks the track, and re-levels so it glides without binding. If the glass is heavily etched or the frame corroded, the pro quotes a replacement enclosure rather than sinking money into a failing unit.
See the difference
Before
After
Before
After
Before
AfterMr-Glass Products We Service & Install in Westchester
We service and install the full range of Mr-Glass residential glass products. That includes Mr-Glass Semi-Frameless Shower Enclosures, Mr-Glass Frameless Shower Doors in both 3/8-inch and 1/2-inch glass, and Mr-Glass Sliding Glass Shower Doors. We also work with Mr-Glass Custom Mirrors and Glass Shelving. On the enclosure side, we handle Frameless Glass Shower Enclosures, Walk-In Shower Installation, and Tub-to-Shower Conversion for Westchester bathrooms. Tight lot lines and 1950s to 1970s CBS construction shape how these installs run, so we assess the backer and framing before specifying hardware.
We Also Service These Brands
We’re not a single-brand shop. Alongside Mr-Glass, we work with KraftMaid cabinetry, Cambria, Silestone, and Kohler fixtures across our remodeling work. That breadth matters when a bathroom project pulls in a vanity, a countertop, and a glass enclosure together. You get one contractor and real choices at every price point.
FAQs – Mr-Glass Construction Service in Westchester
No. We are an independent Mr-Glass service provider, not affiliated with or authorized by Mr-Glass. We repair, install, and service Mr-Glass equipment with quality parts that fit it.
Yes. We source OEM Mr-Glass rollers, hinges, and sweeps when available, and use tested aftermarket stainless-steel and brass hardware that meets or exceeds original specs when they aren’t.
Most hardware repairs, like replacing rollers or a sweep, are done in a single visit. A new enclosure install or tub-to-shower conversion depends on the bathroom and how the framing and backer look once we open it up. Your written estimate sets the timeline.
We cover Mr-Glass Semi-Frameless Shower Enclosures, Frameless Shower Doors in 3/8-inch and 1/2-inch glass, Sliding Glass Shower Doors, and Custom Mirrors and Glass Shelving. We also handle walk-in shower installs and tub-to-shower conversions.
Not if the work is done properly. We use parts that fit and keep the enclosure operating the way it was built to, which is what a warranty expects. We’re not factory-trained or certified by Mr-Glass, so we can’t speak for the manufacturer’s terms, but we can tell you what we did and document it.
Typical estimated ranges are below. The written estimate sets the final price, and every quote is free. Call (888) 334-0815 for an exact quote.
| Service | Typical Estimated Range |
|---|---|
| Walk-In Shower Installation | $4,500 – $12,000 |
| Tub-to-Shower Conversion | $3,500 – $10,000 |
| Shower Replacement | $3,000 – $8,500 |
| Bathroom Remodel | $9,000 – $28,000 |
| Bathroom Vanity Installation | $800 – $3,000 |
Call (888) 334-0815 to schedule your free estimate. Estimates are free.
Book Your Mr-Glass Service in Westchester, FL
Whether it’s a sliding door that’s jumped the track, a sagging frameless enclosure, or a full tub-to-shower conversion, we’ll assess it and give you a written line-item quote. Call (888) 334-0815. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Westchester Construction Co.