Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Westchester Homeowners Choose Cover Construction
Westchester Construction Co is an independent Cover construction and service provider in Westchester, FL. We install, repair and service Cover’s shower enclosure systems, and we install them the way a frameless glass unit actually has to be installed here: on solid backing, with tight tolerances, and with hardware that fits Cover’s drilled glass and track profiles. The difference comes from field work, not from a badge.
Westchester is a built-out, unincorporated Miami-Dade suburb with no vacant land left, so projects here are mostly rebuilds and additions on mid-century lots rather than new construction. That matters for Cover work because most of these jobs are in bathrooms that were closed up decades ago, and every one runs through Miami-Dade County’s post-Surfside 40-year recertification and inspection regime instead of a small-town permit office. You get the framing picture looked at while the enclosure is out.
To be clear: we are not affiliated with, authorized by, or partnered with Cover. We’re an independent provider that services Cover equipment, and we also handle KraftMaid, Cambria, Silestone and Kohler products. Call (888) 334-0815 to book a free estimate. We answer 24/7, and fast dispatch runs from 7am to 7pm.
Why Trust Westchester Construction Co for Your Cover Construction?
Our technicians have up to 9 years of experience, and a good share of that has been spent standing in front of Cover enclosures working out why a door binds or a hinge end has opened a gap. That familiarity matters more than it sounds. Cover makes frameless glass walk-in enclosures, semi-frameless sliding doors, aluminum-framed bi-fold doors, and custom-cut glass panels for tub-to-shower conversions. Each one fails in its own way, and each one has to be set against a wall that can carry the load.
We use quality parts that fit Cover equipment. When a roller is worn flat or a sweep has gone hard, we replace it with hardware sized to that enclosure’s glass and track, not a generic piece that gets “close enough.” Poorly matched aftermarket hardware is the fastest way to misalign a Cover door and undo the water control it was engineered for.
Everything we do is warranty-safe. We read the glass, we check the mounting, and we work in a sequence that leaves the enclosure’s original sealing logic intact. We don’t claim any manufacturer authorization, and we don’t pretend to. What we offer is careful hands and straight answers about what your Cover unit needs.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Cover Construction Problems We Fix in Westchester
Cover enclosures don’t fail all at once. They fail at the small moving parts, and usually in a pattern you can predict once you’ve seen enough of them.
- Roller and track wear on sliding doors. The rollers on a semi-frameless sliding Cover door flatten over the years, and the door starts to bind, jump off the track, or leak at the floor guide. It’s wear, not a structural fault. Fresh rollers and a re-leveled track bring the glide back.
- Hinge sag on frameless enclosures. A frameless Cover panel is heavy, and it hangs on hinges screwed into a wall. If the wall studs were never blocked properly behind the tile, the hinge slowly pulls and a widening gap opens at the glass-to-wall joint. The fix is proper blocking and re-hanging the glass, not a new unit.
- Seal and sweep deterioration. Bottom sweeps and jamb seals harden with age and heat. Once they do, water escapes onto the bathroom floor and works into the subfloor around the curb. It looks like a minor drip and behaves like a slow leak.
- Mineral and corrosion pitting. Westchester’s humidity and heavy summer rains keep bathrooms damp, and hard water leaves mineral film that pits aluminum frames and cloud the glass coating over time. Routine cleaning and the right protective routine slow this down considerably.
- Improperly templated glass on older remodels. A panel cut without checking the actual wall plane can leave an uneven gap that no sweep will seal. When we see this, we measure the opening honestly and tell you whether a re-cut panel or a hardware adjustment is the real answer.
Cover Parts & Our Repair-vs-Replace Approach
We don’t stock OEM or genuine Cover parts, and we don’t claim to. What we do is source quality parts that fit Cover’s hardware sets and glass drilling, so the enclosure closes the way it was designed to. That distinction is the whole game with frameless and sliding doors.
Our repair-or-replace call follows a simple rule. If the glass panels are sound and only the hardware and seals have failed, repair usually makes sense, and it’s the better value. If the tempered glass is cracked or chipped, replacement is the answer, full stop; patching a compromised panel isn’t something we’ll do. We’ll tell you which situation you’re in before any work starts. Call (888) 334-0815 for a free estimate.
Our Cover Service Process – Step by Step
- 1
Diagnosis. We look at the enclosure’s real condition: hinge anchoring, track level, sweep condition, and whether the wall behind it can carry the load. In a Westchester bathroom remodel, this often means checking framing that’s been behind tile for decades.
- 2
Repair or install. We replace the worn hardware, add blocking where it’s missing, or set a new Cover enclosure with the correct shimming and sealing. Nothing gets forced into place.
- 3
Test. We operate the door through its full swing or slide, check the floor guide and seals, and run water to confirm the enclosure holds before we call it done.
- 4
Warranty-safe closeout. We leave the installation in a state that respects Cover’s original design, so you keep the protection the unit was built with.
See the difference
Before
After
Before
After
Before
AfterCover Products We Service & Install in Westchester
We handle Cover’s frameless glass walk-in shower enclosures, semi-frameless sliding shower doors, aluminum-framed bi-fold shower doors, and custom-cut glass panels for tub-to-shower conversions. Frameless walk-ins are the most common request in Westchester’s older bathrooms, where owners are trading a tub for a cleaner open shower. Sliding and bi-fold doors suit tighter footprints, which is common on these small mid-century lots. Whatever the configuration, we service it with parts that fit and an eye for how the unit seals against a Florida bathroom wall.
We Also Service These Brands
Cover isn’t the only name we know. We also work with KraftMaid cabinetry, Cambria and Silestone surfaces, and Kohler fixtures, so a bathroom or kitchen project that touches more than one brand stays with one contractor. That’s the practical advantage of a multi-brand team over a single-brand specialist. One point of contact, one schedule, consistent work across the room.
FAQs – Cover Construction Service in Westchester
Yes, in most cases a Cover shower door can be repaired rather than replaced. When the glass is intact and the trouble is worn rollers, hinges or sweeps, new hardware restores the door’s glide and seal. Replacement is the call only when the tempered glass itself is cracked or chipped. Call (888) 334-0815 for a free estimate.
A hinge-side leak on a frameless Cover enclosure almost always traces to hinge sag, and hinge sag traces to wall studs that were never blocked properly. As the heavy glass panel hangs, the hinge pulls and a gap opens at the wall joint. Re-blocking and re-hanging the glass closes that gap; a new sweep alone won’t fix it.
Cover enclosures hold up well in Westchester’s humidity when they’re installed correctly and maintained. The real enemies are mineral film, dampness trapped around seals, and pitted aluminum frames from hard water and constant moisture. Routine cleaning and replacing hardened sweeps early keep a Cover unit working for years. Our technicians have up to 9 years of experience with these conditions.
Yes, a tub-to-shower conversion with a Cover walk-in enclosure is one of the most common bathroom projects in Westchester. The tub comes out, the drain and rough-in are checked, and a custom-cut Cover glass panel is templated to the new opening. Typical estimated conversions run $3,500 – $10,000, with the written estimate setting the final price. Call (888) 334-0815 to schedule your free estimate.
Genuine Cover glass and hardware carry the manufacturer’s markings on the glass and on the fittings. A generic panel usually has none, or has a marking that doesn’t match the door’s hardware. If you’re unsure, we can look at it during a visit and tell you what you’re working with before any work is quoted.
Cover enclosure work in Westchester typically falls in these estimated ranges, and the written estimate sets the final price:
| Cover Service | Typical Estimated Range |
|---|---|
| Frameless Glass Shower Enclosure (Walk-In Shower Installation) | $4,500 – $12,000 |
| Tub-to-Shower Conversion | $3,500 – $10,000 |
| Shower Replacement | $3,000 – $8,500 |
| Small Bathroom Remodel | $5,000 – $12,000 |
| Bathroom Remodel | $9,000 – $28,000 |
Call (888) 334-0815 for an exact quote; estimates are free.
Book Your Cover Service in Westchester, FL
Whether your Cover enclosure needs new rollers, a re-hung frameless panel, or a full walk-in install in a Westchester bathroom, we’ll look at it, tell you what’s actually wrong, and quote it in writing. Independent service, quality parts, straight answers. Call (888) 334-0815 to schedule your free estimate. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday.
Written by the team at Westchester Construction Co.