Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Westchester Homeowners Choose CGI Construction
We provide independent CGI construction service in Westchester, Florida, installing and repairing CGI’s all-wood and plywood-box cabinetry, Shaker and slab-front door styles, soft-close hardware and semi-custom vanity and pantry lines. What makes our CGI work different is that we fit the product to your room and your budget rather than to a dealer program, and we tell you honestly when a failing box should be replaced instead of patched.
Westchester is a built-out, unincorporated suburb of Miami-Dade with no vacant land left. Construction here is almost entirely rebuilds, additions and tear-downs on mid-century lots, and every CGI cabinet job runs through Miami-Dade County’s post-Surfside 40-year recertification and inspection regime rather than a small-town permit office. The work is shaped as much by tight lot lines and county inspectors as by the actual building.
To be clear about who we are: Westchester Construction Co is an independent CGI service provider. We’re not affiliated with, authorized by, or a dealer for CGI. Call (888) 334-0815. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Westchester Construction Co for Your CGI Construction?
Our technicians have up to 9 years of experience, and a good share of that time has been spent inside CGI cabinets rather than reading spec sheets about them. We know how the all-plywood box goes together, how the Shaker and slab fronts behave over a few humid summers, and which hardware sets keep the soft-close feel the line is bought for.
Parts matter here. We use CGI hinges, glides and touch-up and finish kits where they exist, so the soft-close action and the finish match the rest of the run. When a part is discontinued, we go to quality aftermarket hardware that fits the box correctly rather than forcing something close enough. That approach keeps the installation warranty-safe: nothing we hang, shim or adjust should give a manufacturer a reason to deny a claim on hardware you already own.
We’re a full-scope residential construction company, not a cabinetry-only shop. That means a CGI kitchen can sit inside a larger project – new impact windows, a roof, a bathroom rebuild – without you coordinating three separate contractors. One contractor, every trade.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common CGI Construction Problems We Fix in Westchester
CGI cabinets fail in predictable ways here. The subtropical Miami climate – intense sun, heavy summer rains, high humidity, hurricane season from June through November – is hard on any cabinet line, and the failure patterns below are what we see most often in Westchester homes.
- Thermofoil and laminate faces peeling at the edges. The door face lifts where moisture wicks into the edge band, usually at the bottom of upper cabinets and around the sink. Air-conditioned interiors with high ambient humidity accelerate it. Once the substrate under the face is exposed, patching rarely holds.
- Soft-close glides losing dampening or sagging. This usually isn’t hardware failure. Cabinets shimmed out of level on an uneven slab floor put the drawer box in a bind, and the glide wears unevenly through its travel. The fix is re-leveling and re-adjusting before replacing anything.
- Swollen boxes at sink bases and dishwasher bays. Particleboard and MDF cores swell when a slow leak goes unnoticed behind a cabinet. A soft, crumbly bottom panel or a door that no longer closes flush is the tell. This is the one failure where replacement is usually the honest answer.
- Painted and stained finishes checking and fading near west-facing windows and sliders. Afternoon sun through a slider does more damage to a cabinet finish than most homeowners expect. The finish dries, checks and loses color on the sun-facing run while the rest of the kitchen looks fine.
- Doors and drawers out of alignment after a floor or countertop change. New flooring or a new counter changes the plane the cabinets sit on. Hinges and glides need a full re-adjustment through their travel, not a quick tweak.
CGI Parts & Our Repair-vs-Replace Approach
We don’t stock, carry or order genuine CGI parts, and we’re not a CGI dealer. What we do is source quality parts that fit CGI equipment: CGI hinges, glides and finish kits where they’re available, and quality aftermarket hardware when an OEM part has been discontinued. The goal is a soft-close action and finish that match the rest of the run.
Repair versus replace comes down to the substrate. A loose hinge, a drifted glide or a scratched door face is a repair. A swollen box, a soft bottom panel or a run of faces peeling off exposed core is not – refacing or replacing those cabinets is more honest than patching a failing substrate, and we’ll tell you so.
If you’re weighing the two, call (888) 334-0815. Estimates are free, and the written estimate sets the final price.
Our CGI Service Process – Step by Step
- 1
Diagnosis. We open every affected cabinet, check box cores for swelling, test each soft-close glide and hinge through its full travel, and look at the floor plane under the run. On older Westchester homes we also note whether the cabinets sit level on the slab or were shimmed to compensate.
- 2
Repair or install. For repairs, we pull the affected doors, replace damaged faces or cabinets, and re-level the boxes. For new installations, we set and shim the CGI cabinets to the floor and wall plane, then hang doors and drawers with the hardware adjusted to the room, not to the factory setting.
- 3
Test. Every drawer and door gets cycled through its full travel. We check soft-close catch, door reveal alignment and that no cabinet binds against a counter, appliance or adjacent run.
- 4
Warranty. You get a written record of what was replaced, what was adjusted and which parts were used, so any manufacturer warranty claim on the cabinets stays clean and documented.
See the difference
Before
After
Before
After
Before
AfterCGI Products We Service & Install in Westchester
We service and install the CGI product types that show up in Westchester kitchens and baths: all-wood and plywood-box base and wall cabinets, Shaker and slab-front door styles in painted or thermofoil finishes, soft-close drawer and door hardware sets, and the semi-custom vanity and pantry cabinet lines. That covers a straightforward cabinet swap, a refacing job and a full kitchen buildout. We don’t claim to stock any of it. What we bring is the fitting, leveling and hardware adjustment that decides whether a CGI cabinet run still feels right after five humid summers.
We Also Service These Brands
CGI is one line among many we work with. We also handle KraftMaid cabinetry, Cambria and Silestone engineered stone surfaces, and Kohler fixtures, which matters when a CGI kitchen also needs a countertop or a sink and faucet replaced. You choose the brand; we handle the build. That keeps you from hiring a separate contractor for every material in the room.
FAQs – CGI Construction Service in Westchester
No. We’re an independent CGI service provider, not affiliated with or authorized by the manufacturer, and we’re not a CGI dealer. We install, repair and service CGI cabinets with quality parts that fit them.
Yes. We use CGI hinges, glides and touch-up and finish kits where they exist, and switch to quality aftermarket hardware only when an OEM part is discontinued. We don’t stock or order genuine CGI parts as a rule.
Most cabinet adjustments and hardware replacements take part of a day. A full CGI cabinet installation in a Westchester kitchen typically runs several days depending on box count, countertop timing and whether the floor plane needs correction first.
We cover CGI’s all-wood and plywood-box base and wall cabinets, Shaker and slab-front door styles in painted or thermofoil finishes, soft-close hardware sets, and the semi-custom vanity and pantry lines.
Proper installation and hardware adjustment shouldn’t void a manufacturer warranty, and we keep a written record of parts and adjustments so any claim stays documented. We can’t speak for CGI’s warranty terms – read those yourself before work starts.
CGI cabinet installation in Westchester typically runs $4,000 – $13,000, and a full kitchen remodel runs $14,000 – $45,000. These are estimated ranges; the written estimate sets the final price. Call (888) 334-0815 for an exact quote – estimates are free.
| Service | Typical Estimated Range |
|---|---|
| Cabinet Installation | $4,000 – $13,000 |
| Countertop Installation | $2,000 – $6,500 |
| Kitchen Remodel | $14,000 – $45,000 |
| Small Kitchen Remodel | $9,000 – $20,000 |
| Backsplash Installation | $800 – $2,500 |
One pattern worth knowing before a pro walks in: CGI thermofoil faces curling at the bottom edges while a couple of soft-close drawers stop catching. The usual cause is moisture wicking into the door edges, combined with glides that were never adjusted after the boxes were shimmed onto an uneven floor. A qualified local pro pulls the affected doors, checks the box cores for swelling, replaces the damaged faces or cabinets, and re-levels and re-adjusts the hardware through its full travel before reinstalling.
Book Your CGI Service in Westchester, FL
Whether it’s a peeling CGI door face, a drawer that won’t catch, or a full CGI cabinet installation in a Westchester kitchen, we’ll give you a straight read on repair versus replace. Call (888) 334-0815 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Westchester Construction Co.